carry a 0.5 mm ASA cap on every face, so colour and grain sit in the cap, not in a coating. This guide shows where each profile fits — terraces, pool decks, walkways, facades, screens and soffits — and what to confirm before ordering.
What is ASA co-extruded decking and cladding?
ASA is a co-extruded cap — acrylic-styrene-acrylonitrile — extruded over a PVC–WPC core at the die head, so cap and core leave the line as one body. The cap is 0.5 mm on every face: front, back, both long edges and the clip groove. The cap carries the colour and the grain; the core carries the strength. Between them, a continuous fibre reinforced layer raises bending strength and holds dimensions under load and heat. T*Home's ASA range has five decking models, 138–150 mm — three ASA-capped boards and two PVC film laminated boards — and nine cladding models, 121–240 mm, in shiplap, fluted, three-rib and four-rib sections. Trims, clips and screws are colour-matched. Twelve colours are held in stock across decking, cladding and trims, so a facade and the deck below it read as the same project.
Where does ASA decking fit?
Three jobs, three picks. For a terrace or garden, use the 140 × 25 mm solid or hollow board with a concealed clip for a closed face underfoot. Around a pool or on a marine platform, the same 140 × 25 mm board drains through the joint and takes full sun and salt. For a walkway or a commercial deck, take the wider 150 × 25 mm or 140 × 24 mm board, with closer frame centres for heavier traffic. Standard length is 2.9 m. Deep-embossed wood grain is standard on both faces; brushed and wire-brushed textures, dual-tone caps and 3D relief are available on the same profile.
Where does ASA cladding fit?
For a facade, use the 122 × 16 mm shiplap on ventilated battens: a shadow line, screwed at the seam, hidden by the next panel and dry cavity behind the board. For screens and details — partitions, gates, column wraps — use the 190 × 20 mm and 219 × 25 mm ribbed sections. For soffits and ceilings, the 224 × 21 mm four-rib and 240 × 24 mm fluted panels cover wide spans and shaded undersides. Cladding carries the same cap as the decking, so a facade and its terrace hold one colour scheme through the seasons. Wall cladding is fixed with screws at the seam — drive an .A2 stainless steel screw through the tongue at the joint into the batten, one screw at every batten crossing; the next panel slides over the tongue and covers the screw heads. No clips are used: cladding is decorative, not load-bearing.; the tongue-and-groove overlap reads as a thin shadow line and the back vent gap keeps the cavity dry.
How do decking and cladding work as one system?
One cap, one palette, one kit. The twelve colours are capped from the same run, so decking, cladding, fascia and corner trim ordered together come out of the same batch — a trim never arrives a shade off the board. Boards, edges and fixings ship as one kit: one trim, one stainless clip, one A2 screw. L skirting comes in 45 × 45 mm and 30 × 30 mm, closing the wall base and the deck edge with the same cap on both legs. Clips and trims ship at 3–5% spare, so a site never stops for a missing pack. On the frame, decking runs at 400–450 mm centres for residential use and 300–350 mm for commercial or heavy use; the gap is 2–3 mm with the standard clip, 6–7 mm only where drainage is wanted. Spacing depends on board profile, span and expected load.
What should you confirm before ordering?
Four things. First, the model, the colour and the quantity — send them and we reply with a quote within 24 hours. Second, the colour: swatches shift on screen and in daylight, so confirm against a physical sample before ordering in bulk. Third, the order size: MOQ is 100 m² per colour for decking and wall cladding; custom colour matching, deep embossing and dual-tone caps are available subject to MOQ and tooling. Fourth, the numbers that matter for specification: bending strength 55.4 MPa, water absorption 1.29%, B1 fire retardant, service range −30 to 80 °C, and a 20-year colour performance expectation based on 4,000 hours of ASTM G155-25 accelerated testing — an expectation, not a warranty term. Test reports are available on request. A 140 × 25 mm solid board loads about 1,200 m² per 40HQ, as a reference value.
Frequently asked questions
What is the difference between ASA decking and WPC decking?
ASA decking carries a 0.5 mm ASA cap on every face, with the colour and grain in the cap. WPC decking comes uncapped (01 Normal Standard, 02 3D Embossed) or with a co-extruded cap (03 Capped). Which ASA colours are available?
Twelve colours: C01 Black Walnut, C02 Red Pear, C03 Walnut, C04 Beech, C05 Light Grey, C06 Caramel, C07 Cedar (Ost), C08 Cedar, C09 Golden Sandalwood, C10 Oak, C11 Teak (Ost), C12 Teak.
Can ASA decking go around a pool?
Yes. The 140 × 25 mm board drains through the joint and takes full sun and salt, with a 20-year colour performance expectation behind it.
Do the decking and cladding match in colour?
Yes. They share one cap and one palette, and boards ordered together come from the same run. Confirm the colour on a physical sample before ordering in bulk.
What is the minimum order quantity?
100 m² per colour for decking and wall cladding.
How do I get a quote?
Send the model, colour and quantity to eva@thomestyle.com (WhatsApp / WeChat +86 15956288470) and we will reply within 24 hours.